Slurry Pumps
Heavy-duty centrifugal slurry pumps built on the proven AH/HH hydraulic range. Thick wear liners, high head per stage and fully interchangeable metal
View series
Slurry pump manufacturing · Shijiazhuang, China
Heavy-duty slurry pumps built to keep running
Centrifugal slurry pumps, gravel pumps and wear parts for mining, dredging, power and oilfield service.
ISO 9001 quality systemCE markedIn-house foundry & machiningSelection reply within 24 h
12Product series
100+Pump models & sizes
40+Export countries
24 hEngineering response
Product ranges
Pump families for every duty
Every pump is built around replaceable high-chrome or rubber wetted parts, so the casing, bearing frame and baseplate keep working while wear components are renewed on site.
Gravel & Dredge Pumps
Large-passage gravel and dredge pumps for sand, gravel and coarse solids, built to pass tramp material without choking.
View series
Vertical Sump Pumps
Cantilevered vertical spindle pumps for sumps, pits and tanks, with no submerged bearing and no shaft seal.
View series
Froth & Flotation Pumps
Pumps engineered for air-entrained froth in flotation circuits, keeping the impeller flooded where a standard pump would lose prime.
View series
FGD & Power Plant Pumps
Limestone and gypsum slurry pumps for flue gas desulphurisation, with materials selected for chloride and pH conditions.
View series
Oilfield & Drilling Sand Pumps
Mission-compatible centrifugal sand pumps for drilling solids control, mud mixing and well service.
View series
Wear Parts & Spares
A05 high-chrome, R55 rubber and duplex stainless wet-end parts, cast from our own patterns and dimensionally interchangeable.
View seriesPopular models
Featured pumps
AH / AH(R) Heavy-duty slurry pump
Horizontal, end-suction, double-casing pump for strong abrasive slurries in mining, coal, metallurgy and power. Rubber (R) version for fine particles.
View details
HH High-head slurry pump
Same layout as AH but with a larger volute and impeller for higher pressure; suited to long-distance transport and multi-stage series installation.
View detailsG / GH Sand & gravel pump
Wide, unobstructed passage for large solids. Used in dredging, sand washing, dam desilting and coarse tailings.
View detailsMagnum
The workhorse: centrifugal pump for drilling-fluid transfer, desanding and mud mixing. Sizes 3x2x13 through 10x8x14.
View detailsLiners & throat bushes
Suction and discharge side liners, volute liners and throat bushes for AH, HH, G, ZJ and ZGB casings.
View detailsSP / SPR Vertical sump pump
Cantilevered vertical spindle pump with no submerged bearing and no shaft seal. Metal (SP) or rubber-lined (SPR) wet end, column lengths built to the pit depth.
View detailsWhy Anze
Engineering, casting and testing under one roof
↻
Interchangeable by design
Wet-end parts follow the original patterns, so liners and impellers drop into existing pumps without re-piping.
⚙
In-house foundry
A05 high-chrome castings poured, heat-treated and machined in our own works - chemistry and hardness controlled.
✓
Tested before it ships
Every pump runs on our test bed at duty point; performance and vibration reports ship with the pump.
✈
Export-ready logistics
Standard models ship in 7-15 days; custom alloys 20-30 days. Single-unit orders accepted.
Applications
Where our pumps work
Mining & tailings
Mill discharge, cyclone feed and long-distance tailings lines.
Dredging & sand
Cutter suction dredgers, sand winning and barge unloading.
Power & FGD
Limestone and gypsum slurry in flue gas desulphurisation.
Flotation & froth
Aerated pulp transfer in concentrator circuits.
Oilfield & drilling
Solids control, mud mixing and trip tank service.
Chemical & corrosive
Rubber-lined wet ends for acidic and corrosive slurries.
Our works
From casting to test bed
Shijiazhuang Anze Heavy Industry Machinery Co., Ltd. designs and manufactures centrifugal slurry pumps under the JIGU brand.
News
Latest from Anze
2026-11-02
Slurry pump selection: five numbers to get right before you quote
Head, flow, maximum solids size, specific gravity and pH decide most of the specification. A short checklist for engineers sizing a new duty.
2026-11-02
Why rubber liners outlast metal in fine grinding circuits
A practical comparison of R55 natural rubber and A05 high-chrome in cyclone feed and flotation duty, with wear-life observations from three customer sites.
2026-11-02
Anze Heavy Industry ships twelve AH slurry pumps to a copper tailings project
A repeat order from a South American copper concentrator: twelve AH-14/12 units for tailings transfer, supplied with A05 wet ends and expeller seals.
FAQ
Frequently asked questions
Are your pumps interchangeable with Warman / Mission originals?
Yes. Wet-end dimensions follow the original patterns, so liners, impellers and casings fit existing pumps and foundations without modification. Anze is an independent manufacturer and is not affiliated with Weir Minerals or Mission.
What is your minimum order quantity?
One unit. Most spare-part and single-pump orders ship within 7 to 15 days.
Which wear material should I choose?
A05 high chrome for coarse, sharp, high-head duties above 60°C; R55 natural rubber for fine particles below about 6 mm and corrosive slurries.
Can you match my current pump without a nameplate?
Send photos, dimensions and duty conditions; our engineers identify the series and quote equivalents within 24 hours.
Need a pump specification or a quote?
Send us your duty conditions and our engineers reply with a selection within 24 hours.